Heat pump installation · Maur
At a glance
Small project
CHF 33'500 – CHF 61'400
Typical project
CHF 42'400 – CHF 78'900
Large project
CHF 55'600 – CHF 105'200
| Project | Quantity | Low | High | Per unit |
|---|---|---|---|---|
| Small project | 80 m² | CHF 33'500 | CHF 61'400 | CHF 600 |
| Typical project | 160 m² | CHF 42'400 | CHF 78'900 | CHF 400 |
| Large project | 280 m² | CHF 55'600 | CHF 105'200 | CHF 300 |
Computed with our estimator for Maur (regional factor included), standard finish. Only the project size changes.
Included
Not included
In Maur, the federal building register lists 2'209 residential buildings and 4'980 dwellings. These municipal benchmarks help put your home in context, but do not replace an individual assessment.
55 % built before 1980
Construction year does not reveal past renovations: check the current insulation condition.
53 % · Heating oil
This distribution describes recorded buildings, not your system's consumption or efficiency.
| Energy | Heating | Hot water |
|---|---|---|
| Gas | 5 % | 4.9 % |
| Heating oil | 53 % | 44.7 % |
| District heating | 1 % | 0.8 % |
| Heat pump | 31 % | 6.5 % |
| Electricity | 4 % | 32.7 % |
| Wood | 6 % | 3.4 % |
| Solar thermal | 0 % | 4.9 % |
Each line gives the share of buildings using that energy, separately for heating and for hot water. The two columns do not always reach 100%: some buildings combine two systems, or reported none.
A standard non-condensing boiler is usually older and less efficient.
For your renovation projects in Maur, the official building register provides essential reference points. The median building volume stands at 1163 m3, which serves as a key indicator for scaling your future heating or insulation improvements. Please note that these volume figures are based on a limited sample size of only 12 buildings measured according to SIA 416 standards, indicating partial data coverage. Since information regarding renovation years and heritage protection is not recorded in the register, you should consult the municipality directly early in your planning phase to clarify any potential restrictions or requirements for your specific property.
Source : OFS — RegBL (export communal complet). Existing residential buildings; percentages of recorded values.
The first step is to check the available energy options. First check whether your area can connect to a priority district heating network, as this may be more advantageous depending on the local configuration.
Then, analyze your home's insulation to determine the required thermal capacity. The local design outdoor temperature sets the heat pump's capacity needed to efficiently heat your home.
A professional thermal assessment is recommended to avoid costly oversizing. Use the RenoIndex calculator to get a realistic cost estimate in CHF for your project in Maur.
Also, ensure that the necessary permits are obtained before work begins. A good installation is not limited to technical performance; it must also ensure harmonious coexistence within your neighborhood in Maur by minimizing noise pollution.
There are several technologies available : air-to-water, geothermal, or air-to-air. The choice depends on your land, your budget, and your current heating system.
Air-to-water systems are very popular in renovations because they adapt easily to existing radiators or underfloor heating. If you have suitable land, geothermal energy offers exceptional efficiency but requires more significant drilling work.
Consult professionals about the comparative advantages for your specific situation in Maur. The RenoIndex estimator helps you compare budgets for different technical solutions in a few clicks.
Rigorous preparation is the key to success. Anticipate the necessary electrical and hydraulic connections. Replacing an oil boiler with a heat pump often requires compliance upgrades for the internal installation.
In addition to direct purchase and installation costs, plan a budget for possible masonry work or heat distribution system adjustments.
To get a clear view of the amounts involved, use RenoIndex for free for an estimate in CHF adapted to the prices in the canton of Zurich. This allows you to adjust expectations before contacting companies.
1. Estimate
Set a budget range with the estimator.
2. Grants
Apply before work starts.
3. Quotes
Compare at least 3 quotes.
4. Permit
Check with the municipality whether a permit is needed.
5. Works
Follow the site and do a written handover.
No specific grant listed for this work. Maintenance tax deductions may still apply.
2829 Vermes · about 89.5 km
The website presented under the name Imeri Chauffage et Sanitaire Sàrl offers plumbing, heating and solar thermal work, while F. Imeri Sàrl’s registered purpose refers to a scrap metal business.
imeri-sarl.ch2824 Vicques · about 93.9 km
Specialist since 1968 in sanitary installations, heating (gas, oil, wood, renewable energy), and tinsmithing with 24/7 emergency repair service.
sanit.ch2824 Vicques · about 93.9 km
Buchwalder Sàrl in Vicques has specialized in the installation, repair, and renovation of heating and sanitary systems since 1966.
buchwalder-sarl.ch2824 Vicques · about 93.9 km
Gyger Haustechnik specializes in sanitary installations, heating systems, bathroom renovations, and tiling work.
gyger-co.chSuggestions from the commercial register by distance and activity. Not an endorsement or partnership.
In general, a well-maintained heat pump has a lifespan of between 15 and 20 years. Regular maintenance by a professional is essential to guarantee the optimal performance and longevity of your heating equipment.
Yes, replacing a heating system almost always requires a building permit at the municipal level. Check the specific requirements with the technical department of the municipality of Maur before starting your work.
Costs vary depending on the type of pump and the configuration of your house. To get a precise price range in CHF for Maur, use the free RenoIndex tool to estimate your overall budget.
Yes, it is possible, but it depends on the required flow temperature. Oversized radiators allow for a lower water temperature, making the heat pump more efficient. A heating engineer must evaluate your existing installation.
